Skip to main content

How to make 200 Watt Inverter





                        200 Watt Inverter


This circuit diagram. Built based on IC CD4047 inverter circuit can
convert 12VDC to 220VAC and 50-60Hz frequency and Square

wave signal. In this use IC CD4047 Square wave Oscillator at 50Hz and use LM358 for buffer circuit. The transformer is 12V-0-12V Primary and 220V Secondary. Power Transistor IRF250 x 2 For driver transformer 220V ac and other Power Transistor mosfets
IRF540 is also use. IC CD4047 will work in the astable
multivibrator mode. In the CD4047 are pin 10 and 11 are Q and ~Q from. This AC is given to the step up transformer of the secondary coil. 220VAC- up to 200w transformer from 12V lead acid battery.

 

200 Watt Inverter circuit diagram:-



PCB Board:-



 

Components Required:-



  • 12v Battery
  • Op-amp LM358
  • IC – CD4047
  • RED LED(1)
  • 470R ohm Resistor (2)
  • 1k ohm Resistor (3)
  • 390k ohm Resistor (1)
  • Variable Resistor 100k
  • 200W transformer (12V-0-12V)
  • Power Transistor IRF250 x 2
  • Bulb or any AC appliance
  • Capacitor (0.01uF)



 CD4047:-





















1. IC-4047 CMOS as Simple astable multivibrator
2. output will be a square wave
3. Positive- or negative-edge trigger
4. Output pulse width independent of trigger pulse duration
5. Retriggerable option for pulse width expansion
6. Long pulse widths possible using small RC components
7. Fast recovery time essentially independent of pulse width
8. Pulse-width accuracy maintained at duty cycles


 Operational Amplifier LM358:-














1.  LM358 is a Dual Low Noise Operational Amplifier which have two Op Amp in a single chip.

2.  LM358 consists of two independent, high-gain, frequency-compensated operational amplifiers designed to operate from a single supply over a wide range of voltages.

3. LM358 is a Dual voltage comparators inside.

4. This is a general purpose op amp which can be configured in many modes like comparator.


youtube:-



 

 

 

 

Comments

  1. I have irf250 can i use it??

    ReplyDelete
  2. please send me a sample pcb for testing thank you

    ReplyDelete
  3. Fan or led tv k leye kitna amor k transformer lega

    ReplyDelete
  4. Can i glow 2 100w bulb by this cricuit and
    . how much watt transformer will be used... Please rply me

    ReplyDelete
  5. CAN I USE Z44 pls tell me bro.

    ReplyDelete
  6. Can I use one NE555 MONOSATBLE mode with 4047 ASTABLE mode ?

    ReplyDelete
  7. How to charge battery again

    ReplyDelete
  8. https://www.electronicsforu.com/electronics-projects/hardware-diy/12v-battery-charger-absorb-float

    ReplyDelete
  9. https://www.electronicsforu.com/electronics-projects/hardware-diy/12v-battery-charger-absorb-float

    ReplyDelete
  10. The King Casino | New Zealand's Best Online Casino
    who owns the King Casino brand and the Royal Vegas Hotel & 온카지노 Casino brands. Find out how you can become a member of The King Casino's 10bet portfolio 더킹카지노 in

    ReplyDelete

Post a Comment

Popular posts from this blog

Simple clap switch

clap switch Required Components:- 1. 4017 - IC                         - 1 2. 741 - IC                           - 1 3. Resistors(10K)                - 1 4. Resistors(1K)                  - 5 5. RED led                          - 1 6. Diode (In4007)               - 1 7. Green Led                       - 1 8. MIC                                 - 1 9. Relay(9v)                         - 1 10. BC547                            - 1 11. variable resistor(1k)        -1 12. Battery / Adapter(9V)     -1 Circuit Diagram:- YouTube:-

Power Amplifier Circuit using IC TDA2030

Features of TDA2030 Amplifier:-  1. TDA2030-IC range of voltage between 9 V to 24 V  2. TDA2030A is a monolithic IC intended for use as low frequency class AB amplifier.  3. Output power 18 W at VS = ±16 V / 4 Ω with 0.5% distortion  4.  High output current  5. Very low harmonic and crossover distortion  6. Short-circuit protection  7. Thermal shutdown Required Components:-  stereo jack pin                         - 1  TDA2030 IC                           - 1  Resistors(100K)                      - 3  Resistors(4.7K)                       - 2  Resistors(10R)                        - 1  Diode (In4007)                       - 1  Capacitor(.1uf)                       - 1  Capacitor(22uf)                      - 2  Capacitor(2200uf)                  - 2  Capacitor(2.2uf)                     - 1  variable resistor(100k)           - 1  Battery / Adapter(12V)          - 1 TDA2030 Amplifier  circuit diagram:- PCB:- youtube:-